● 31 lines
● 48 extensions

● 3 modular loop start line ports with Caller ID capability
● 8 modular enhanced tip/ring (ETR) extension ports
● The first two provide power failure transfer to
  the first two lines
● 2 slots for PCMCIA cards
● 2 touch-tone receivers
● 1 music source port (RCA type)
● 1 modular loudspeaker paging port
● 1 modular SMDR port
● 1 modular jack to connect to an optional
  contact closure device

● 3 modular loop start line ports with Caller ID capability
● 8 modular ETR extension ports
● 2 touch-tone receivers

● 3 analog CO lines
● 6 ETR only station ports
● 2 full function ETR station ports with full tip/ring
  functionality

● 4 modular loop start line ports with
  Caller ID capability
● 2 touch-tone receivers

● 12 ETR station ports
● No power-failure transfer capability
  (no CO lines on 012E module)
● Supports 48 stations
● Supports full T/R capability along with ETR

● SDSL capability
● Provide router functions, up to 16 voice channels
● PARTNER Advanced Communication System R4.0
  will only support one 1600 DSL module and that
  module can only be used in slot 1 of a 5-slot carrier
  or in the expansion slot of a 2-slot carrier.
● No power failure transfer capability

● Maximum 2 devices per extension jack
       ● can be a system phone plus a standard
        device or 2 standard devices
     ● total Ringer Equivalency Number (REN) on
        jack not to exceed 2.0
● No more than 1 system phone per jack

Dimensions and Weights (Approx)

● 45 watts (154 BTUs/hr.) per PARTNER®
  Advanced Communications System processor
  module during normal power consumption
● 85 watts (290 BTUs/hr.) per PARTNER®
  Advanced Communications System processor
  module during maximum power consumption
● 10 watts (35 BTUs/hr.) per 400 module, normal
  and maximum power consumption
● 42 watts (147 BTUs/hr.) per 308 module, normal
  and maximum power consumption
● 16 watts (56 BTUs/hr.) per 1600 DSL module,
  normal and maximum power consumption
● 45 days to 6 months memory backup with 2
  AAA-size standard alkaline batteries (IEC LR03)

● 68306 16 Mhz processor
● 256 Kbyte RAM
● 512 Kbyte Flash ROM
● Custom VLSI DSP ASIC—16-bit, 52 MHz

● Ringing voltage: +5 VDC, -140 VDC peak to
  peak; trapezoidal wave shaping
● 35 to 38 Volt talk battery
● Ringing frequency: 20 Hz

● Accepts 2 Volts at 50 Kohms maximum input
● 0-18 dB attenuation

● Operates up to 150 feet (45.72 meters) from
  control unit using 24 gauge solid conductor wire
  if 2 contact closure devices are used; up to 800
  feet (243.84 meters) from control unit using 24
  gauge solid conductor wire if 1 contact closure
  device is used
● Install the contact closure adjunct in the same
  building as the control unit; cannot be installed
  out-of-doors
● Has 3 terminals per contact closure, providing a
  normally open and normally closed function for
  each contact closure
● Maximum contact voltages and current
     ● 30 VAC, 1 Amp
     ● 50 VDC, 1 Amp

● 1200 baud
● 8 data bits
● XON/XOFF protocol
● Line feeds
● No parity
● 2 stop bits
● Carriage return

● Mount on a wall at least 2 feet (0.6 meters)
  from the floor (wall mounting required)
● Locate within 5 feet (1.5 meters) of the network
  interface jacks and a properly grounded electrical
  outlet not controlled by a switch, using supplied
  7-foot (2.1 meter) cords
● Operating temperature of room: 32 to +104 F
  (0 to +40 C), not in direct sunlight
● Humidity 15% to 90% non-condensing
● For proper ventilation and easy replacement of
  modules, provide the following maximum clearance
  around the control units:
     ● 5-slot carrier: 1 foot (0.3 meter) clearance at the
       top and sides, and 2 feet (0.6 meter) clearance at
       the front and bottom
     ● 2-slot carrier or stand-alone PARTNER® Advanced
       Communications System processor module:
       1 foot (0.3 meter) clearance at the front, top,
       and right side, and 2 feet (0.6 meter) clearance
       at the bottom and left side
● Locate in an area free of excess moisture, corrosive
   gases, dust, and chemicals

● U.S. and Canada: 90-130 VAC, 50-60 Hz,
  3-prong outlet separate ground, separately
  fused at 15 Amps
● Other countries: 90-264 VAC
  (220 VAC fused at 10 Amps)
● Grounding to comply with Underwriters
  Laboratories (UL) 1459

● Installation of a telephone or other standard
  (tip/ring) device in another building requires
  the following In-Range-Out-of-Building (IROB)
  protectors to protect the control unit and device
  from electrical surges:
   ● System phone: 2 IROB protectors
   ● Standard phone: 1 IROB protector plus
     1 carbon block protector
● Installation of a contact closure adjunct controlled
  device outside the building requires a surge protector
  to protect the control unit from electrical surges.

● U.S.: Meets UL 1459 Issue 2
● Canada: Meets CSA C22.2.225
● All other countries: Meets IEC950 Second
  Edition and EN60950 Second Edition

● FCC Part 68 approval
● FCC registration number (U.S.) See the label
  on the side of the control unit
● PCC Part 15 approval
     ● Class A: 5-slot configuration; 2-slot
        configuration with PARTNER® Messaging
     ● Class B: PARTNER® Advanced Communications
        System stand-alone configuration; 2-slot
        configuration with 308EC, 400EC, and PARTNER®
        Advanced Communications System processor
        modules
● REN (outside line jack): 0.9A per line jack
● Jack type: RJ11C
● Loop start lines

● IC CP01, Issue 7
● IC registration number (Canada): See the
   label on the side of the control unit
● IC CS03, Issues 6 & 7
● Load Number = 7
● Loop start lines

● For all other countries, please contact relevant
  jurisdiction authorities